What is UNS S30400?
What is UNS S30400? This grade of steel is an austenitic stainless steel. It is the most common grade of stainless steel, offered in an extensive types of variants, forms and surface finishes than any other type of stainless steel.

General characteristics

Core 301/4310 has a lower chromium and nickel alternative to Core 304/4301 with high work hardening capacity. It is a good choice for applications subjected to high mechanical loading. Core 301/4310 is an austenitic CrNi stainless steel with high carbon and relatively low nickel content. It shows a high degree of work hardening on mechanical deformation.

Core 301/4310 is used in applications where corrosion resistance and a combination of high mechanical strength and good formability are needed. Due to its strong tendency to work hardening, Core 301/4310 can absorb an increased amount of energy during deformation. It can be delivered in temper rolled condition with different strength levels.

SS 301 is an austenitic Chromium-Nickel stainless steel capable of attaining high strength with moderate cold working. The combination of high strength and good ductility makes it suitable for numerous mechanical switches as well as electronic and computer spring components.

The alloy is readily formed in the annealed temper. Ductility decreases with increased cold rolled strength but not to the degree that would occur with SS 302. It is not recommended for deep drawing. SS 301 can be welded by all conventional processed except oxy-acetylene. The weld should not make contact with electrolytes to prevent intergranular corrosion. SS 301 is resistant to atmospheric corrosion and is additionally resistant to mildly corrosive mediums. The combination of narrow strength bands and close thickness tolerance provided by Hamilton Precision Metals is the key to repeatable response characteristic in spring and switch applications.

Typical applications

• Springs
• Press plates
• Conveyor chains
• Mixer blades
• Sinks

Chemical Composition

The chemical composition of grade 301 full hard stainless steel is outlined in the following table.

Element	Content (%)
Iron, Fe	73
Chromium, Cr	16.0-18.0
Nickel, Ni	6.0-8.0
Manganese, Mn	2.0
Silicon, Si	0.75
Carbon, C	0.15
Nitrogen, N	0.10
Phosphorous, P	0.045
Sulfur, S	0.030

Physical Properties

The following table shows the physical properties of grade 301 full hard stainless steel.

Properties	Metric	Imperial
Density	8.03 g/cm3	0.290 lb/in³

Mechanical Properties

The mechanical properties of grade 301 full hard stainless steel are displayed in the following table.

Properties	Metric	Imperial
Tensile strength	1276 MPa	185100 psi
Yield strength (@strain 0.200 %)	965 MPa	140000 psi
Compressive yield strength (longitudinal)	793 MPa	115000 psi
Fatigue strength (endurance limit; test details not reported)	552 MPa	80100 psi
Elongation at break (in 2" (50 mm))	9.00%	9.00%
Charpy impact	150 J	111 ft-lb
Hardness, Brinell	382	382
Hardness, Rockwell C	41	41

Available Sizes:

SS 301 is available from Hamilton Precision Metals as strip product in thicknesses from 0.0005” to 0.050” (0.0127 mm to 1.27 mm) in widths up to 12.0” (304.8 mm). It is also available in foil as thin as 0.000200” (0.00508 mm) in widths of 4.0” (101.6 mm) maximum. The material conforms to ASTM A666, MIL-S-5059, QQS-766, and UNS 30100.

If you need product information or price, please fill in your contact information in the form below, we will usually contact you within 12 hours. You could also email me info@lyapm.com to get prompt reply.

1. Stock view

   

2. Processing and Technology for heating processing

Cutting processing      Quenching              Tempering                  Annealing

       

3. Quality testing

1.      Inspection Institution

Shanghai Fuda Testing Technology Group Co., LTD. Nanjing Branch  

Focus on analysis, testing, testing, r & D four service areas. Analysis fields include component analysis, formula analysis, failure analysis, structure analysis, methodology development and validation, raw material quality control/evaluation, consistency evaluation, feature analysis and other directions; The testing field involves physical and chemical properties testing, toxic and harmful substances testing, flame retardant performance testing, reliability testing and other directions; The testing field involves energy spectrum, electron microscope, spectrum, chromatography, mass spectrometry and other directions; The r&d field involves formula development, formula upgrading, formula customisation, cooperative research and development and other directions.

Beijing Zhongke Chemical Technology Research Institute 

It is a chemical technology research institution based on scientific research and testing. They adhere to paying equal attention to basic research and applied research, and combining applied research and technology transformation, developing into a comprehensive research institute characterised by "task-oriented disciplines". Approved by the relevant national departments, the company has become a third-party analysis and testing technology service unit, and has obtained CMA qualification certification. It has carried out research and development and design, analysis and testing, test and verification, generic processing, information and intellectual property services, providing public services for innovation of technology-based enterprises. Supported by the government innovation Fund, the institute has been awarded as a national high-tech enterprise.

   

2.Inspection Machining

     

   Metal composition testing machine                      Computerised Materials Torsion Testing Machine                Metal bar composite rod bending tensile strength testing machine

       3. Material test certificate

     4. Packaging 

    In the steel export activities, we also need to pack the steel to prevent the steel from being scattered in the transportation process. In the hoisting process, it is necessary to lift the steel. So steel is very necessary in the export process. Below is the picture of packaging：

According to the requirements of the state of steel materials, the use of binding, bare, frame, pallet.

Packing standard: according to the following national standard requirements (the parts beyond the requirements will be specified separately)

GB／T191 packaging-pictorial marking for handling of goods

GB／T4857 (all parts) basic test for transport packages

GB／T4879 rustproof packaging

GB／T5048 damp-proof packing

GB／T7350water-proof packing

GB／T8166 Package cushioning design

GB/T4892-1996  Hard straight square transport packaging size series

GB/T13201-91 Cylinder transport package size series

 GB/T16471-1996Design and make the size limit of transport package 

5. Logistic

       

1. Company profile

Luoyue Precision Metal established in 2018, is a leading Stockists and global distributor for Metal Raw Materials like Steel/Aluminum/ Stainless steel/Copper/ Nickel Rods, Bars, Plates, Sheets,Pipes, fittings, fasteners, Inconel alloys, Wire and Wire-Mesh to customers from aerospace, automotive, electronics, precision manufacturing, ordnance, marine, shipbuilding, oil & gas, power plant and construction.

The company has a high-precision, high-efficiency modern processing site, CNC machine tools and complete testing and inspection technology, and introduces international advanced technologies.

           2. Certificates. (Business certificate/ISO9001/Trading certificate/SGS/FormE)

                  .      

          3. Our customers 

                 Customer visits 

           4. Past Inquiry

                  .     

   1.Customer Rating

       

FAQ
1. Q: Are you a manufacturer?  
 A:No, we are not manufacturers. We have our own warehouse and our own company. I believe we will be the most suitable supplier for you.  
2. Could we visit your factory?  
 A: Sure, we welcome you to visit the factory , check our production lines and know more about our strength and quality.  
3. Q: Do you have quality control system?  
 A: Yes, we have ISO, BV, SGS certifications and our own quality control laboratory.  
4. Q: Can you arrange the shipment for us?  
 A: Yes, we have designated sea freight and railway freight forwarders with decades of experiences and we get the best  price with earliest vessel and professional service.
5. Q: How long is the delivery time?  
 A: Generally it is 7 days if we have the exact goods in our stock. If not, it will take around 15-20 days to get goods ready for delivery.  
6. Q: Can I get some samples?  
 A: We are glad to provide free samples to you, but we do not offer the freight.  
7. Q: What is your after-sale service?  
 A: We provide after-sale service and offer 100% guarantee on our products.  
8. Q: What is your MOQ?  
 A: 2 Tons  

Contact us